- #Samsung washer and dryer front loader code#
- #Samsung washer and dryer front loader series#
Turn off the unit for 10 seconds and then turn it on again.ģ.
#Samsung washer and dryer front loader code#
It can also mean that the unit senses a small clog while draining.įAULT CODE SOLUTION/FIX: Clean the drain filter.ġ. SAMSUNG FAULT CODE DEFINITION: Your washer is not draining. Press the Power button to turn off your washer, then turn it on again. SAMSUNG FAULT CODE DEFINITION: The door will not unlock.įAULT CODE SOLUTION/FIX: Make sure the door is firmly closed. SAMSUNG FAULT CODE DEFINITION: Your washer has tried to fill but has not reached the proper water level. SAMSUNG FAULT CODE DEFINITION: Water temperature control problem. SAMSUNG FAULT CODE DEFINITION: Your washer failed to lock the door. SAMSUNG FAULT CODE DEFINITION: Door is open when washer is running.įAULT CODE SOLUTION/FIX: Close the door tightly and restart the cycle. SAMSUNG FRONT LOAD WASHER FAULT CODE: dS or D5
SAMSUNG FAULT CODE DEFINITION: Door is unlocked when washer is running.įAULT CODE SOLUTION/FIX: Press the Power button to turn off your washer, then restart the cycle. SAMSUNG FAULT CODE DEFINITION: Unbalanced load prevented your washer from spinning.įAULT CODE SOLUTION/FIX: Redistribute the load, press the Start/Pause button. When it finishes washing, “End” and “SUdS” codes will blink in turn.įAULT CODE SOLUTION/FIX: To prevent it, cut down on detergent Then, the unit will go back to the operation. The unit is put on hold until the suds are reduced. SAMSUNG FAULT CODE DEFINITION: Too many suds are detected during the washing session. SAMSUNG FRONT LOAD WASHER FAULT CODE: SUdS SAMSUNG FAULT CODE DEFINITION: System failure SAMSUNG FRONT LOAD WASHER FAULT CODE: SF1, SF2, SF3
SAMSUNG FAULT CODE DEFINITION: Communication error between SUB PBA and MAIN PBA SAMSUNG FAULT CODE DEFINITION: Ag+ Kit problem. SAMSUNG FAULT CODE DEFINITION: High/Low voltage detected.įAULT CODE SOLUTION/FIX: Restart the cycle. SAMSUNG WASHING MACHINE PROBLEM: Washer has excessive vibration or noisy
Be sure the Detergent Selector dial is in the upper position when using granular detergent. Be sure your washer is running with sufficient water pressure. SAMSUNG WASHING MACHINE PROBLEM: Detergent remains in the automatic dispenser after the wash cycle Reduce the detergent amount for soft water, small or lightly soiled loads. Use high efficiency detergent to prevent over-sudsing. SAMSUNG WASHING MACHINE PROBLEM: Washer has excessive suds Very small loads (one or two items) may become unbalanced and not spin out completely. Use high efficiency detergent to reduce over–sudsing. SAMSUNG WASHING MACHINE PROBLEM: Wash load is excessively wet at the end of the wash cycle Make sure the water supply hoses to the washing machine are connected securely and correctly Use high efficiency detergent to prevent over–sudsing. Be sure the end of the drain hose is correctly inserted and secured to the drainage system. Be sure all hose connections are tight. SAMSUNG WASHING MACHINE PROBLEM: Washer leaks water Make sure both faucets are fully OPEN If WRONG TEMPERATURE or NO WATER The hose filter screens may be plugged. Disconnect the hoses and clean the screens. Also check the water heater capacity and recovery rate. It should be set to deliver a minimum 120☏ hot water at the tap. Make sure the hoses are connected to the correct faucets. Make sure the temperature selection is correct. SAMSUNG WASHING MACHINE PROBLEM: Washer fills with the wrong water temp Check the screens on the inlet hoses at the faucets for obstructions.īe sure washer is plugged into the outlet and is getting power. There may be a pause or soak period in the cycle. For your safety, your washer will not tumble or spin unless the door is closed. Close the door and press the Start/Pause button to start your washer. Plug the power cord into a live electrical outlet. SAMSUNG WASHING MACHINE PROBLEM: Washer stops working Washer water supply hoses – Be sure screens are not clogged and rubber washer is installed 
Press START/PAUSE button to pause and restart programs Open and close the door, then press the Start/Pause button.SAMSUNG WASHING MACHINE PROBLEM: Has no water or not enough water Check the fuse or reset the circuit breaker.
#Samsung washer and dryer front loader series#
Before your washer starts to fill, it will make a series of clicking noises to check the door lock and do a quick drain. (Deactivating the Child Lock function – Press and hold both the Spin and Soil Level buttons simultaneously for approximately 6 seconds) Be sure the Child Lock is not activated. Be sure to press the Start/Pause button to start your washer. Be sure the water source faucets are open. SAMSUNG WASHING MACHINE PROBLEM: Washer will not start
0 kommentar(er)
